We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
I followed the example described in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_nrf52_developing.html#fota-updates
and the loaded the SMP Server example...
Hallo,
currently I test several options in regarding the use of advertising. I have a few nRF52840-DK and use Zephyr 2.7-99 and ncs. I have a question regarding combined...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
In our application, we provide internet connectivity to the WT02C40C module via a mobile...
Hi,
I have a makefile generating an elf and then a hex and bin file for a nrf52 project. Now I builded up a zip file for bootloading. Which works as well.
Now in our CI...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
I want change toolchains, so when i open nrfconnect terminal I can use my own west command. I've read link , link and link
Option in the picture lets me install or open...
Hi,
There were GPIO /SPI Interface headers are given on NRF21540 EK .now how we can connect RF input to TRX pin of NRF21540.
please provide the Understanding of RF input...
Hi
We are looking into connecting an external GNSS antenna to the Thingy91x board. The drawings metion 2 ports J1 and J2 but can't find anything in the docs if these are...
Hi, I am currently outputting some audio (1000hz sine wave) via audio_i2s_blk_comp_cb_register and audio_i2s_set_next_buf (from audio_i2s.h ) through the line out audio jack...
Good morning, I am trying to send data via BLE from a custom board (with the nRF52840 microcontroller) that has sensors, to an evaluation board nRF52840 PCA10056. To do this...
Hello Team,
Please help in guiding to enable L4 security & detailed guide to enable L4 in latest nRF Connect SDK having nRF54L15 chipset on nRF connect SDK 2.7.0
Thank...
Hi there,
I have a small custom board with the nRF52810 that uses the LDO instead of the DC-DC, it also doesn't have the 32KHz LF crystal.
Was able to add this to the...
hi destiny98 i also working on sending string from peripheral to central but central device not able to receive it and show the same message every time, here i attach code...
