Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
I plan to keep the bonded device information in the ring buffer, but there are a few things that puzzled me:
When PM_EVT_CONN_SEC_CONFIG_REQ event is received, .allow_repairing...
Hi,
i am working ANCS example project in nrf14.1.0 SDK, s132.5.0.0 softdevice. i am able to print category of all notifications. i wanted print text message info. is it possible...
SDK13 nRF52 S132.
Hi! Correct I understand and implemented how to make interrupt?
I use gpiote.
void gpiote_init (void)
{
nrf_gpio_cfg_input(INT1, NRF_GPIO_PIN_NOPULL...
Hello,
I am using sdk12.2.2 and nrf52. I am including scan response data in my packet. But every time I am getting extra fields in my raw data as seen in nrf connect app...
Hi
I discovered I strange behaviour using twi.
I am using sdk-14.2.0, and Segger Studio. I started with the twi_scanner projected that I found in examples/peripherals...
We are using the NRF8001 in a product that is potted in epoxy with wireless charging and so completely inaccessible to any outside inputs except through bluetooth. We have...
I have already configured the usb audio class for NRF24LU1+.Then if i want to send data throught the NRF24LU1+ USB Isochronous endpoint,what should I do? Actually I have already...
use the SDK5 14.2.0, NRF52832, pca10040, the ble_peripheral\ble_app_uart\pca10040.
first, UART_EASY_DMA_SUPPORT = 1, run the uart_init(); the current is 1.2mA;
UART_EASY_DMA_SUPPORT...
Hello.
I'm having problems building example project from SDK using Segger Embedded Studio.
I'm using Segger Embedded Studio V3.30 IDE on Linux - Ubuntu 16.04. Using nrf...
I have a 24L01 + evkit in my hand and I want to burn my own program on this board, but I do not know how to burn it in. I have the following 3 questions:
Question 1: Where...
I have SD 4.0.2 + 13.0.0 secure debug bootloader, and I am trying to update it to SD 5.0.0 + 14.0.0 secure debug bootloader. It transfers the data, goes to 100%, but after...
Hi
I am currently working on a BLE mouse device. NRF52832. BLE part works well. However, the mouse stick part is using ps2 protocol. I didn't find USART in NRF52832.
...
