Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Hello, I am developing on a custom board with the nrf5340 and programming through SWD using the nrf5340dk. A few days ago everything was running fine and I was able to continuously...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
i have to interface MT29F4G01ABAFDWB in zephyr rtos but i need help how create overlay file for it(i want to interface it using spi), i already have bare metal drivers for...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
When trying to flash the hello world program onto an Adafruit nRF52840 Feather through a j link it fails with "FATAL ERROR: one or more Python dependencies were missing; see...
In any Wi-Fi firmware that I write with nRF Connect SDK I get this error message in my console logs:
<err> net_icmpv6: ICMPv6 handling failure (-2)
This happens in every...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
i am having a bus fault somewhere in my code, i am trying to use addr2line to identify the source code line that it heppens at, for some reason it shows as if the adress is...
I am trying to connect two thingy:52 and a Polar H10 heart rate monitor simultaneously to nRF9160 dk, but while building the application I am encountering this error. Can...
We are utilizing the nrf5340 alongside the nrf7002 for Bluetooth Low Energy (BLE) and Wi-Fi communication between a wearable device and a host. The host is a laptop connected...
