Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
NRF52840 uses 2.5V power supply. We found that when the voltage drops below 1.7V, even if the voltage returns to 2.5V, the entire system cannot work and JLINK cannot connect...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
Hi ,
I am exploring the peripheral examples from the nRF5_SDK_17.1.0.
I am testing the example code "flash_fds" from the peripherals. I am able to compile the code without...
According to developer.nordicsemi.com/.../migration_sysbuild.html , the config variable SB_CONFIG_BOOT_SIGNATURE_KEY_FILE and SB_CONFIG_BOOT_ENCRYPTION_KEY_FILE should be...
Hello,
I have a custom board based on a nRF9160 SiP. It uses a shared antenna for GPS and Cellular, based on this : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_033...
Hello,
Installing a new computer with de dev environnment I am finding that NCS1.9.2 is not in the available releases.
Is there a reason for this?
Thanks for...
Hi,
I have a customer in Guernsey that received one of our Thingy91 hubs and he's not able to connect.
Here is some troubleshooting facts :
- when he moves to London...
Hello,
I just received a new NRF9160-DK board and I am surprised it has the 4 leds blinking all along.
What does that mean?
I have not found any of this in the startup...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
I'm developing with nrf connect sdk.
I have an peripheral IC with a mcu interface enable pin. This product is very focused on battery life. The peripheral IC has higher...
Zephyr / SDK 2.1.2 / nRF52833, acting as BLE peripheral. My system consists of multiple peripherals, and I want each of these peripherals broadcast its own unique MAC address...
Hi
Is any of this antennas supportet or certified in Norway ? I know thingy 91 use trio mxtend from Ignion.
But is run mxtend certified or do I need to certify it ? Its...
Currently, the nRF5340 Audio is set up and running as follows: In CIS mode, the audio source is I2S
Gateway side: nRF5340 Audio DK I2S settings are default Headset side...
