Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
We are using adp536x to turn on/off the 3.3 V source as to determine the usage of a specific water valve. Unfortunately, whenever we have a circuit connected and turn the...
Hi,
We are starting a process to certify our nR51822 based product for use in the UK, with accordance to new UK regulations
Has there already been a process to certify...
Hi.
I would like to make an app for communicare with a can device. I see that the chip mcp2515 is a popular one .So i purchsed some dev boards with this chip. One of them...
Hello,
I have a question concerning the decryption of a 90 byte AES CTR ciphertext with a given 16 byte key and 12 byte IV (=8 byte nonce, 4 byte counter).
I've tried...
Hi,
I used the nRF Programmer included in nRF Connect to flash the custom PCB. After the update to 2.0.0 J-link is no longer detected under devices. Could you help with...
I was flashing nRF51822 used ST-link, with file hex from SDK example, so now i want flashing a different .hex. How can i do that? I try do like before but I CAN'T
I'm trying to dynamically allocate some data, send it over NUS, and then free it, but I'm not sure when the SoftDevice is done with it and it's safe to free. Would the following...
Launched nRF Connect for Desktop this morning (v3.7.0) and was prompted that an update was available. Performed the update as well as child packages. PPK was updated as a...
Hi, i have a problem with nrf mesh. nRF5_SDK_17.0.2_d674dde
nrf5_SDK_for_Mesh_v5.0.0_src
nRF52-DK(PCA10400)
Android 6 and 10.
Bluetooth 4,1 4,2 5.0.
I use example...
When using USB with CONFIG_NO_OPTIMIZATIONS=y I'm getting a usage fault and Zephyr gives the reason K_ERR_STACK_CHK_FAIL. The fault looks like it occurs in the unnamed thread...
Hi,
In case the FMFU fails or the device gets into some recovery state. Is there a way to get IMEI without enabling the modem library? When the modem is in process of failed...
Hi,
Can you please tell us how to send Hex data using AT#XSENDTO command ?
I am using the "Serial LTE" application. In the old SDK version (v1.6), it was possible to set...
Hello,
I recently saw this post: https://devzone.nordicsemi.com/f/nordic-q-a/71940/low-power-mode-using-saadc-with-ble_app_beacon and I'm interested in the example for measuring...
Hello Kenneth,
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2...
Hello,
I try to port project from IAR to Segger Studio. I followed the guides for porting projects like this and this . So, I did:
- Imported IAR project to SES with internal...
