In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
I would like to ask, if I just want to "Download program", what components on the schematic diagram are needed?
Download program is OK, so first make sure that...
Hi all,
I've found an alexa gadget example but I can't seem to get it running on my nRF52840-DK. The example I've found was located under repository:
https://github.com...
nrfx_gpiote_irq_handler() which is nearly 150 lines of code. All the GPIOs seems to have same priority at the hardware level, how among different GPIO's Interrupts are processed...
Hi, I got an SDK15.2 project that we converted the bootloader to be both serial and ble for the dfu. Unfortunately we have a few units in the field that have only the BLE...
Hi,
I want to schedule timeslots back-to-back, or as close as possible. Question is how close to eachother timeslots can be scheduled?
I read the following about sd_radio_request...
I have a custom BLE service that works correctly with nRF Connect. When I use the API, though, it sends me the same value repeatedly and does not update to reflect new values...
Hi,
I am a developer of IoT systems working for a private firm within Africa. I currently started the development of a cellular IoT solution and my search landed me on the...
Hi,
I've somehow managed to build the gps sample from source within SES, but I can't get the flashed sample to work properly. Everything is fine if I flash the downloaded...
https://devzone.nordicsemi.com/f/nordic-q-a/46388/nrf9160-dk---make-application-from-scratch
I followed the steps from user: Aakash_Soni on this thread. However, when...
Hello,
I am using Segger Embedded Studio IDE v4.52 (64-bit) to develop an application using nRF5340pdk.
My question is this, I cannot find any of the Preprocessor or compiler...
Hi.
I am developing using nRF52820 with SDK 17.0.0 . I test the USBD using the example code(\nRF5_SDK_17.0.0_9d13099\examples\peripheral\usbd_hid_generic), but the problem...
Hi,
I would like to know if it's possible to read advertising data when connecting to the peripheral.
My problem is sometimes when i read the adv data, and then try to...
Hi,
I try configure 2 gpio pins with opposite pull state, one NRF_GPIO_PIN_PULLUP, other NRF_GPIO_PIN_PULLDOWN :
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI...
Hello
We are working on BLE remote based on nRF52810. We are operating it through coil cell. Please let us know is there Internal battery monitoring feature supported by...
