Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I programmed my thingy91 with lte_ble_gateway example, however I want to be able to connect to devices with specific addresses. Can anyone point me in the right direction...
Hi,
I am using pwm driver to generate different square wave of different frequencies in order to drive a buzzer to play melody.
Below is how I init my pwm software module...
I have the following problem:
1 to 3 phones are bonded with an nRF52832
These phones are on the whitelist of nRF52832
nRF52832 goes into Power Off Mode
nRF52832...
Hi,
We are integrating the nRF52840 into a new test apparatus and I am using the nRF52840-DK for development. I have pulled out my unit from storage and it will not power...
Hi,
There was an app timer immediate expiration issue with my project which is using nrf52840 + S DK 15.3.0 on custom board.
So I changed apptimer code to app timer2...
I was wondering why the RSSI Viewer Values are locked to a minimum of -33 dBm. Is there any reason for that and is there a workaround to get lower values? Currently I am using...
Hi,
I currently need to stream 1000 data samples over BLE, each data sample is 14 bit value, hence i'll be using a short integer but i'm confused as to how to send it over...
HI,
we are using the nrf52840 in our new poroduct and we are running the zephyr/ncs RTOS on it.
for real time reasons I need to read from a SPI bus upon a GPIO trigger...
Hi all,
I would like to ask whether is there any details description of the matching network circuitry of NFC for NRF52840 in the datasheet.
The only information I could...
Hello,
I am following the instructions given in this ticket https://devzone.nordicsemi.com/f/nordic-q-a/57896/pdm-interface
When I call the nrfx_pdm_enable_check() the...
Hello，
We are developing wearable devices. 17 sensor terminals send data to the receiver at a frequency of 60hz per second. The data sent by 17 sensors at the same time...
Hello,
I'm interested to know whether the continuous integration and continuous deployment (CICD) is possible on nrf52840 board using Segger Embedded Studio ?
if yes,...
Hi
I currently have a nRF52833 DK which I am using as a transmitter. I also have a custom board with a nRF52811 SoC with an antenna array to act as the receiver for AoA...
Hi,
I am trying to add PWM in my application. My application uses application timer, SPI (my own written code just like CMSIS) and BLE for smartphone communication.
Everything...
