Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
This question is similar to the feature request: devzone.nordicsemi.com/.../sdk-12-x-0-future-feature-requests
I have to evaluate if we buy Tracealyzer ( percepio.com/....
Hi.
I have a problem to understand what is the difference in SFR registers IEN1 and INTEXP.
Bit 2 in both of them is responsible for enabling 2-Wire completed interrupt...
Hi,
We are currently developing an app which require DFU.
As part of the bootloader development we would like to use the SWO in order to do a printf debug.
In the app...
Hi there,
I am looking to double check the state of NRF52840 while its reset is active.
I have found this thread regarding the NRF52832 ( https://devzone.nordicsemi...
Hi,
I am using sdk12.2.2 and customised nrf52 boards. I am storing 9000 records with 7 bytes each in flash.
After sometime I am getting buffer space full error and I am...
Hi!
I am developing anapplication on NRF52 DK. I need to preserve value between software resets and to do so i tried to use GPREG .
To set value i use code:
//set value...
Hello, I am a student studying firmware
I want to use SPI and UART in one project at the same time.
The soft program uses KEIL and is the latest version. Code generation...
I just received the PPK and use it for the first time.
I am trying use the PPK to monitor the current of an external board.
SW2 is set to 'external' and SW4 is set to...
I have downloaded both "nRF5_SDK_15.0.0_a53641a" and "thingy_sdk_v2.1.0".
After that I tried to build the "main.c" file of " thingy_sdk_v2.1.0" in keil uVision5 but it showed...
My nRF52840 custom boards seem to be unable to boot without RTT viewer started of JLink commander connected.
The hardware configuration is taken from the nRF52840 PS 1.0...
I'm currently trying to update data periodically in the advertising response packet. After successfully initializing and starting advertising, I configure srdata within a...
What is the difference between setting a pin output (to drive an LED) with this set of commands:
nrf_gpio_cfg_output(5);
nrf_gpio_pins_set(5);
and this set of commands...
i use sdk14.2 52832 i use uart
UART0_CONFIG_USE_EASY_DMA =1 consumption ~2.1mA
UART0_CONFIG_USE_EASY_DMA =0 consumption ~650uA
Is this a normal phenomenon, is it true...
Hello !
I'm Omar Rosas from Newark / Farnell tech Support.
I have a customer that he need's to know if there is a enclouser or housing for this part number NRF51822...
Hello,
Few days ago our CI builds which were written with Mesh SDK 1.0.0 started failing and it turns out that 1.0.0 was removed from https://www.nordicsemi.com/eng/nordic...
