I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hey there,
We are currently evaluating the nPM1100 to power several circuits (nrf52, IMU, LEDs).
Our device is tiny, and we want to use a coin-cell battery ( ML2020 from...
Hello,
I am using EMDS to store data to flash under certain conditions. The implementation is pretty basic and follows the specification and example in the SDK (v2.1.2)...
Hello nordic team ,
We are using nrf5340 DK and below mentioned are the Specifications used:
1) Visual studio code
2) nRF5340-DK hardware board (PCA10095)
3) Flash...
Hi,
I am currently trying to use SPI for the nrf9160. I tried building the SPI_BITBANNG sample for the nrf9160dk_nrf9160_ns board for the nrf9160dk that I have.
However...
Hello everyone,
Can someone help confirm if the Timer and PWM modules on nRF52840 can only use the high frequency (HF) clock source (1 MHz or higher) and cannot run from...
Hello,
update to NCS2.2.0,VScode, nRF5340DK
C:\ncs\v2.2.0\zephyr\samples\bluetooth\periodic_sync\
no change any code,got error,
*** Booting Zephyr OS build v3.2.99...
Hello,
I am using the nrf52 for development purposes, during the development I need to power cycle the device approximately ~1000 times, no flash writes in between. Does...
Hi,
for device power managment, i want to power down/disable uart0 that is being used by the Peripheral UART sample. it is giving errors when doing it via the .conf and...
Ive been trying the last few Sdk versions to evaluate the matter examples without luck. With 2.2 released yesterday I jumped on that hoping it would clear up my issue, but...
i have been practicing normal built in application from https://academy.nordicsemi.com/lessons/lesson-1-nrf-connect-sdk-introduction/ . While moving to the next stages i discovered...
Hello,
I've purchased nRF52840 DK 3.0.0 2022.34 1050279741 and device protection remains after power up, even if I disable it.
Current behaviour :
1. nrfjprog...
Hello developers, I am using nRF52833 chip for Mesh sensor application.
The picture below is my mesh network model. 1. The model includes devices such as Sensor Server,...
When trying to compile a zigbee light switch example for the nrf5340-cpu_app target using visual studio using the zigbee fota prj file, the application compiles only once...
brief:
The Zigbee version fo the example was ported to matter. Both standards use ZAP files for the definitions, but have smaller differences in their specification. The...
