I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi,
I downloaded the project for PCA10040 with HID Mouse in ...\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs . From Iphone and computer, I could...
Hello,
in my project i want to use watch dog timer in ble_app_uart_pca10040_s132 but am getting error as shown in image1, even after including driver files and paths
...
hello,
I'm trying to use RSSI Viewer for my custom board - problem is I need to change UART pin.
How do I make my own FW/binary for RSSI viewer?
My custom board uses...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
I'm testing with the new rev of the nRF52832 (build code QFAAGB on the package), and I'm not able to observe behavior that makes sense to me per the updated product spec....
Currently working on a nrf52dk_nrf52832 kit. I have a SPI flash that I am trying to use - I am using the nrf SDK ncs v1.9.1.
I know I can use any of the GPIO pins for SPI...
Hello
I have a mesh node that needs to broadcast a custom BLE packet
To start advertising I call bt_le_adv_start and it works as expected.
I'm curious about the error...
Hello,
I'm in nRF Connect SDK 1.5 and I have to change the baudrate of UART1 at runtime. I have to use Zephyr UART Functions. I have tried the function uart_configure()...
