Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I am using an nRF chip and the nRF SDK for 1st time and I think I am still at the steep part of the learning curve.
My problem is that I cannot get the log from my custom...
We are developing a device that communicates with a remote management system via tcp sockets over LTE. We are using the NRF Connect SDK 1.4.0 with modem firmware mfw_nrf9160_1...
Hello,
I want to transfer analog values via BLE to a external Device. The SAADC is initialize for 2 channels, triggered by RTC-timer and i've get the right values from both...
Hi,
I wonder if it is possible in the nrf91-device to read how much data there is left on the SIM-card.
Where is that information stored?
How does one normally get the...
We using Android Phone (OPPO A53 Android 5.1) and some custom tablets (Android 9.0), to start add custom board as BLE mesh node. But sometimes the reconnection failed even...
Working with the GPS sample.
Builds fine on 1.5.0
on 1.5.1 building with west I get
-- Application: /opt/Nordic/ncs/v1.5.1/nrf/samples/nrf9160/gps
-- Using NCS Toolchain...
I'm trying to upload image asset binary files onto a custom hw that uses the nrf52833 mcu. I use mcumgr for performing DFUs and I would like to use it to upload the binary...
I would like to enable access protection on my device, ie no debugger or flash access. Going through the docs, it looks like I’d have to do a few registers to get access protection...
Hi
I'm new to zigbee programming, but as i understand it is possible to make a zigbee mesh with routers only to decentralize to network.
I have tried to start with a...
Hi,
The most recent version of nRF Toolbox v5.0.4 for iOS cannot see or connect any of my devices (nrf52832, SDK 15.3.0, s132_6.1.1) in the NUS/UART section of the app...
I've recently update to 1.6.1.
I'm testing with SLM, only modification is using UART2 to support communication with an external mcu on another board.
HTTP client interface...
I'm currently trying to send a HTTP body payload that includes "\r\n" in the data payload. I'm getting an "OK" response before I have sent the complete payload.
The problem...
Hi,
I use the nRF52832 with SDK14 and no softdevice.
The MISO on oscilloscope is correct but value in the receive buffer is wrong (can be any value). Unfortunately...
Hello,
Sometimes we don't get a fix when seeing 6 satellites with highest 27dB and lowest 18dB signal strength. And sometimes we are able to get a fix with a GPS fix even...
Hello,
I use NRF52832 with SDK 17.0.2.
I run app timer and pwm driver independently ok.
I merged App timer with PWM Driver. But only PWM run, I can't make app timer...
