Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Are there any examples of libuarte enabling both uarts in the nRF52840 at the same time? I have been trying now for a full day and keep having problems with what options to...
Hi,
I have an app based on freertos_hrs example (nRF52832, SDK14.2)
I'm trying to get it into low power(sleep) mode, however the idle task keep on running and the system...
Hey all. I was testing DFU over USB on an nRF52840, SDK 17.0.2 and I can't seem to get the actual application to run after a successful DFU. I generate my own keys, use them...
Hello,
SDK51 appears to be an inconsistency with how various BLE related events are handled in the SDK. Multiple BLE event handlers may be registered using the NRF_SDH_BLE_OBSERVER...
I'm currently implementing a DFU "controller" in C on the nRF9160 for performing serial DFU with the nRF52840 and believe I have discovered a bug.
My firmware image was...
Hi
I'm using nrf52 DK with SDK V17.0.0
Currently, I'm using Single Buffer to send Data through BLE.
However, I want to use Double Buffer instead of using Single Buffer...
I might be dense here, but please bear with me and clarify something. I am looking at the SPI bus as drawn on the nRF52840. According to the schematics (PCA10056 - nRF52840...
Hello,
Background: I have a custom board that contains nRF52832 module and exposes UART pins (RX, TX, RTS, CTS). I have developed an application using nRF5 SDK v17.0.2....
I'm using SDK 17.0.2 And I found that when the Scan timeout is not working,
Debugging I found that when the nrf_ble_scan_on_timeout function is called, the source of the...
I have an nRF5340 development kit. I can flash a custom application into the app processor. However, when I try to flash the peripheral_lbs sample, I'm getting the error shown...
The hrs.c has the following code.
/* Heart Rate Service Declaration */ BT_GATT_SERVICE_DEFINE(hrs_svc, BT_GATT_PRIMARY_SERVICE(BT_UUID_HRS), BT_GATT_CHARACTERISTIC(BT_UUID_HRS_MEASUREMENT...
I have added the following modification to "ble_app_hids_mouse" example for pca10040 s132.
I want to add a peer whose IRK is known as follows,
void peer_add() { memcpy...
Hello, guys.
We are have nRF52840DK board and Zephyr NCS 1.4.2 development environment.
I am trying to include two PWM channels in the code and control them independently...
Still haven't seen coded phy support with nRF Connect for Desktop for receiving advertisements. With the fact that support from devices is slim, how are we suppose to test...
Hi, Currently I am working on a sensor project with nrf52832. I am having problems optimizing the battery so let me ask the whole circuit as below when the operation will...
