I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I am in the process of migrating an existing project from 2020 to the newest version of Zephy/Nordic. I am having issues with the I2C bus. I created a test project using the...
Hello, I'm trying to connect my nrf7002dk board to wifi with Zephyr. I'm using this sample : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/wifi/sta/README...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2). I see that with this example the boot time of the...
I am using the nRF54L15 and NCS SDK v3.0.2 in my project. I need to wake up the board via interrupts from a pressure sensor and a gyro sensor.
The GPIO requirements are...
Hello
I compiled the zephyr example ../zephyr/samples/drivers/i2s/output
The SCK and MCK Signal do have both the same frequency. The bit positioin on MSB in not in the...
I’m implementing static passkey security in a BLE peripheral using nRF52810 with SDK 17.1.0. I have added a feature where the device disconnects automatically if the user...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
Hello,
I am trying to get confirmation regarding if I should expect to receive DeviceShadow events through the nRF Message Routing Service.
https://docs.nordicsemi.com...
Hi.
I made the smallest system module using nRF52840. The schematic diagram is as follows.
My reference design for power supply is as follows,
For Firmware....
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
I am using nrf5340 audio dk, v3.0.2 SDK. I added CONFIG_BT_TINYCRYPT_ECC=n in prj.conf and got this error: C:/ncs/bumble/hci_uart_0806/prj.conf:23: warning: attempt to assign...
Hello,
You have an outstanding bug related to buffer leak in Bluetooth Mesh suspend-resume operation, NCSDK-31962 https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf...
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
Do you give us some software workaround to use SPI (P2.08-MISO, P2.09-MOSI )
The Hardware design refers to datasheet v0.9, connecting P2.08 as MISO and P2.09 as MOSI. From...
