What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hi,
I am new to embedded device development and I am wondering if I could get some help on SPI control from nrf51422/51822 chip with dev kit to AD9837 wave generator. I...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
Is there a set date for the release of a tracker SW with working GPS? And secondly, will there be a step by step instruction how to upgrade the software on the dev. board...
Hello,
I'm an Embedded system student and I would like to make an extension for ZigBee for which I need to make changes to the underlying ZBoss stack.
Is it possible for...
Hi!
Most of the project's application code is written in C++.
SDK headers are guarded with the extern "C" therefore when including no problems arise with linkage.
The...
