SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi,
i am using nrf51822 interface with mpu9250 and i want to detect a tap without using of DMP feature of mpu motion sensor. my application requirement is low current consumption...
Hi,
sending some data from nRF52840 (DK or dongle) to a host computer via USB. When nRF52840 is connected to a "powerfull" host, all goes ok; when connecting to a "less...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
hello,
Now i transplant pwm_library programming to ble_app_uart_c(central) in SDK15.0.
But i found the program cann't run in NRF52 DK.
I found it build no errors but...
Hello,
We are evaluating now a new project and I am struggling to get a feeling about one moment of Thread network and its particular implementation with nRF52840.
In...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
Hi,
I'm using SDK 13.1, SoftDevice 4.0.5 on nRF52832. I have an app which runs for a long time but will occasionally enter the hardfault handler from an address within the...
Hello,
I try to send multi notification in one connection interval, but I can only send one notification.
Hardware
Peripheral: nrf52832 costumed board (with BMD-300...
Hi,
I'm using nrf52 custom board designed for our project,For this we have P0.09 and P0.10 as rx and tx used for uart, when i configured this two pins as rx and tx it is...
Hi
I am running on a nRF52832 chip with following software stacks
Mesh SDK v3.1.0
nRF SDK v15.2.0
Softdevice v6.1.0
I am working on a use-case where I am processing...
Hi
I want to get a certification. I need your help because I am not currently in DTM mode.
The procedure I checked is as follows.
1. J-LINK , USB to Serial Converter...
Hello to all,
I am using nRF52840 with SES SDK15.0 version. My device is goes into sleep mode after sending data to server. But when woke up device for first reading data...
Hi,
Can someone please tell me in what scenario would a device advertise with two different addresses at the same time?
My device is an nrf52382 based custom PCB...
