What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
hi.......
i am facing the issue while i am transferring the data via ble to ble_app_uart ...
i am using nrf52382 and segger 15.2v
Here if send the one data over ble...
I use SDK12.2.0. The mobile phone has connected my 51822 device,and then the mobile phone keep away from my 51822 device till to disconnect.how to do that they will connect...
Hi Guys,
I facing issue on one of my project, our HW require 2 set of TWI and one QSPI/SPI. I notice SPI0/1 cannot be used because I need both TWI0 and TWI1 to be supported...
Hi,
I'm trying to adopt my nRF52832 projects to the nRF5 SDK version 15.2.0 and the NRFX drivers framework. I'm using a short app_config.h with NRFX_RTC_ENABLED and NRFX_RTC0_ENABLED...
Hello,
There is a example for the nrf52840 for thread with mqttsn. Although this is just for my personal use I would love to use some kind of encryption for it.
So the...
Hello. I have been trying to work with extended advertising between two nRF52840 boards using the SDK, but have had trouble in setting a long advertisement payload (as in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
