Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hi Community,
I'm learning the sysbuild stuffs, try to upgrade my code to sdk v2.9.0.
Exercise 2 - Adding custom image - Nordic Developer Academy
I'm using nRF5340DK...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
