Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
HI.
We have experienced an additional power consumption of ~200uA @ 1.8V on our board when booting from PowerOnReset compared to a Warm reset. Searching for the root cause...
Hi, We had an issue of our custom build boards were the application firmware could be programmed, but the modem could not be programme because of the error "RootKeyDigest...
have been reviewing the nRF54L15 datasheet but could not find the current consumption specifications for LDO mode. Is it possible to operate the nRF54L15 in LDO mode? If so...
Dear Nordic Semiconductor Support Team,
I am looking for EasyEDA-compatible schematic and PCB reference design files for the nRF54L15-QFAA .
However, I could not find...
Hi, We are in the process of upgrading device firmware (using Nordic nRF9160) from nRF Connect SDK 2.4.2 to nRF Connect SDK 3.4.0 LTS. A number of devices to be upgraded are...
Setup: nRF9151 (LACA A0), production modem firmware 2.0.x, application on NCS 2.9 (modem library). The device has external flash holding both the production modem firmware...
We received the physical part with body marking MPN NRF8001-R2Q32-D , while the manufacturer label indicates MPN NRF8001-R2Q32-R.
Please clarify the difference between these...
Hi,
Our nRF91 fails to register on LTE-M even though it sees suitable cells and PLMNs. Manual PLMN selection fails as well. The network never sends a reject; the modem seems...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
Hello,
I'm using an NRF5340 audio broadcast sink, and the nRF Connect SDK version is v3.4.0.
I've added ble connection related definitions to the code to allow the mobile...
Hi,
Test and verify Bluetooth Mesh NLC functionality based on the NCS 3.2.4 and 54L15 by using mesh light ctrl example.
Modify the following configurations in the...
Hi Team,
USB detection is working correctly on the nRF54L20 controller. However, the USB MSC (Mass Storage Class) implementation is not functioning as expected. The device...
Hi,
Setup:
nRF54L15 with NCS v3.4.1.
NSIB with MCUboot as an upgradable bootloader (S0/S1), built with sysbuild and no Partition Manager.
SMP over Bluetooth.
...
Hi, i currently use nrf54L15 and PPK2 in ampere measurement mode.
nrf54l15-DK is PCA10156 1.0.0 2026.37 and PPK 2 is PCA63100 1.1.2 2026.29
For testing purpose i use the...
