Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Board: NRF52840
SDK: 16
Soft Device: s113
So our board is custom and does not contain a crystal. We are treating P0.00 and P0.01 as GPIOs for button inputs. P0.01 works...
Hi all,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
Hello, I tried to implement the zephyr executing time functions API on my nrf52 hardware and I got the above error. According to my SoC documentation (nRF52833), this hardware...
Dear Devzone:
I am developing the design of a PCB that implements the nRF9160 SiP module, I have doubts about how to make the communication interface to connect the module...
Hello,
I used the nRF Connect plugin for VCS to create a Zephyr/BLE project. It appears this copies many files into the "build" directory which are required to compile the...
I am getting compilation errors when using the DT_ macros to access SPI bus child entries.
Overlay file:
&spi1 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin...
hardware : nRF52840DK-52840
SDK : NCSV1.7.1
IDE:Visual Studio Code
I wanted to printf float value , so I set CONFIG_CBPRINTF_FB_SUPPORT=y in my prj.conf file, my application...
Hello,
I'm using following code to read ADC values. The minimum sampling time I'm able to read the ADC reliably is 60ms. I want to lower it to say 5ms or 10ms.
Is there...
To the kind attention of Nordic support team,
reading at this: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrfxlib/softdevice_controller/README.html#softdevice...
Hello,
I have I am trying out the LPN sample from nRF5 SDK for Mesh v5.0.0 and I have an issue where certain mesh configuration messages (e.g. set publication, add application...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
Hi, I work on custom board, which have NRF52833 and IS25LP016D SPI flash. I tried with SPI flash sample but SPI flash driver IS25LP016D was not found! err message show on...
