Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
Hello,
We have an application based on NRF52832 which runs Nordic UART service and DFU service SDK15.2 SD132V6.0. Now, we need to add “high speed data pipe” and we are...
Hi,
I have been using nRF24 in many projects with Arduino. So far quite good experience.
Now I transfer to STM32 and have a strange problem, I cannot send with STM32 as...
Hi,
Has anyone tried connecting the grove_display to the nRF9160?
http://wiki.seeedstudio.com/Grove-LCD_RGB_Backlight/
I have tried the code below
https://github.com...
Hi All,
I'm trying to understand certificate goes where from AWS-IOT to certificate.h.
when setting a new device, I have these 4 certificates:
also the ROOT CA contains...
I have a custom Characteristic in my GATT that is sending data in Notify mode every 30ms.
In my firmware I use timer to do this with something like this :
Everything...
I'm looking to test the DPPI peripheral on the dev-kit, and to that end I though a good example would be to setup the DPPI peripheral to trigger an event when a button is...
Hi, I am new in the development. I want to interface the relay withe ble module.
But not able to do that. Please any one help me to interface the relay. Thanks in advan...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
