SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I tried to use UART both for NRF_LOG and NRF_CLI. Now it's running but I had a problem that calling to nrf_cli_init caused fatal error 8 - INVALID_STATE.
When I commented...
i have question about nRF52832's bluetuth. xtal is 32M, Cload is 12pf, but the frequency is 2.402199G(tested by Network Analyzer), Frequency differency is 199K. We find that...
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
I am trying to run pb remote example but i'm stuck at command 3 it only shows "Got event 0" not goes further to receive remote uuid.
0> 1) Provision first available device...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
I am new to Nordic and BLE mesh connectivity. I have the following assumptions & queries, Please clarify if I am wrong.
1. Is it possible to implement BLE Mesh using Thing52...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
