I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I recently bought this display that is 64x32 pixels and uses the SSD1306 driver . When running the LVGL Basic Sample with the Zephyr ssd1306 _128x64 shield , the display works...
NRF52840 uses 2.5V power supply. We found that when the voltage drops below 1.7V, even if the voltage returns to 2.5V, the entire system cannot work and JLINK cannot connect...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
Hi ,
I am exploring the peripheral examples from the nRF5_SDK_17.1.0.
I am testing the example code "flash_fds" from the peripherals. I am able to compile the code without...
According to developer.nordicsemi.com/.../migration_sysbuild.html , the config variable SB_CONFIG_BOOT_SIGNATURE_KEY_FILE and SB_CONFIG_BOOT_ENCRYPTION_KEY_FILE should be...
Hello,
I have a custom board based on a nRF9160 SiP. It uses a shared antenna for GPS and Cellular, based on this : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_033...
Hello,
Installing a new computer with de dev environnment I am finding that NCS1.9.2 is not in the available releases.
Is there a reason for this?
Thanks for...
Hi,
I have a customer in Guernsey that received one of our Thingy91 hubs and he's not able to connect.
Here is some troubleshooting facts :
- when he moves to London...
Hello,
I just received a new NRF9160-DK board and I am surprised it has the 4 leds blinking all along.
What does that mean?
I have not found any of this in the startup...
I need to use UART0 of the nRF9161 via Tx(P0.27) and Rx(P0.26) for serial communication. There is no CTS/RTS signal.
I used the code from Lesson 5 of the DevAcademy. i...
I'm developing with nrf connect sdk.
I have an peripheral IC with a mcu interface enable pin. This product is very focused on battery life. The peripheral IC has higher...
Zephyr / SDK 2.1.2 / nRF52833, acting as BLE peripheral. My system consists of multiple peripherals, and I want each of these peripherals broadcast its own unique MAC address...
Hi
Is any of this antennas supportet or certified in Norway ? I know thingy 91 use trio mxtend from Ignion.
But is run mxtend certified or do I need to certify it ? Its...
