I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
I followed the getting started guide for Ubuntu:
https://docs.zephyrproject.org/latest/getting_started/index.html
I can build Blinky, but when building my project I get...
Hey, I'm starting a new project and I think a very good fit for this would be to have all of my code in an application chip and use a nrf52840 trough USB as a connectivity...
SD140
Our Central Application is scanning to connect to a peripheral's MAC address. When the scanned address matches, we call sd_ble_gap_connect(p_addr,..). But, it is...
Hello! I'm trying to reload CMake in an nRF-Connect-SDK project in the CLion IDE. I've been using this guide: https://blog.jetbrains.com/clion/2021/04/using-nrf52-with-cmake...
Hello,
I am writing the device tree for our custom board, which uses an nRF9160 SiP. This approach to configuring the hardware
is new to me, since my experience is with...
Hello,
We are attempting to track down a rare bug in our code that causes the device to occasionally hard fault.
We have been able to catch it three times, twice where...
Hi,
When I connect nRF52833-DK device to the (Windows 10) system, its JLink UART (COM) Port disappears after some time (in about 4 to 5 minutes.) The following screenshot...
hello Nordic
i work with nrf52840 , .. want to move to ncs 1.8
seems that moving to ncs 1.8 forces me to update to zephyr-sdk-0.13.2 (from 0.12.4)
is it really a must...
Hello,
I have added the line CONFIG_DEBUG_PORT_ACCESS=y in prj.conf file and now the project does not open in Segger Embedded Studio (SES).
I am getting this error,
...
Hi,
I am building my Project in an out-of-tree form and up to this point I solely used Segger Embedded Studio to compile our project. I am using a custom board with an nrf9160...
Hi All!
I am using VS CODE studio as an IDE for nrf9160 FW development. Blinky app compiled and work perfectly. But when I compiled the asset tracker/cloud client it gives...
In my code, the parameter definitions like this :
In my application, I used SAADC in SEGGER to convert my analog sensor input to digital and then i want to sent...
