Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
We just started a project to replace an old PAN1720 and decided to use the nRF54L15 based module. So I am just getting started with the VS code and zephry enviroment using...
The UART (Port 2) gets garbled after bt_enable(). This issue does not occur if actively Debugging using Segger.
The issue is also reproducible upon a settings_save_one(...
Hi,
I am using nRF54L15, SDK & Toolchain as 3.0.2 version This is for Hid Keyboard, the problem I'm facing is once connected to one device, manually disconnecting & connecting...
Hello,
There are some issues I have found when I tried to achieve both BLE and ESB features concurrently on nRF54L chips, and some of them I have figured out how to fix...
I have BOARD_ROOT set in both zephyr/module.yml and in CMakeLists, and in my boards folder I have a custom board "boards/nordic/myboard". I have all the necessary files for...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
