Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I want to know the configuration of Nordic's GPIO pins. I only want to use one callback function, but due to the many buttons on my mouse device, it is not possible to configure...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
Hi,
I'm working with a custom PCB, with nPM1300 and a microcontroller.
The problem is that working only with battery the nPM1300 VBUS pin show 2.4V and I cannot put...
Hello community,
I have been using my PowerProfilerKit2 successfully under Windows10 for several years now.
Currently I migrate my main system to Linux and would like...
Hello. I have developed a custom board with nrf52840. I am trying to get it running using a bluetooth hids peripheral example in nrf connect v3.1.0. And the main() runs just...
Hi,
I have a field application with a gateway (central) that connects to multiple peripherals for continuous data streaming, in this case 10 peripherals. I notice sometimes...
Has anyone successfully managed to control an led strip (WS2812) with nRF52840's I2S by any chance? I'm trying to use the led_ws2812 sample ( docs.nordicsemi.com/.../README...
Hi,
I'm working on a custom project and I was able to add and edit the overlay file according to my need till yesterday. Today when I tried to build the project I observed...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
I am following the tutorial on Nordic Dev Academy I have a nrf7002dk board and I flashed the code present here . The problem is even if I configure only one channel and I...
Hi Nordic,
I am currently working with the nRF52833 development board and facing an issue related to the APPROTECT feature. Each time I connect the board, the access protection...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
