Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
We need a simple program that can be used as a terminal program on Windows (with nRF52840 dongle attached) to a remote device running the BLE UART service.
Essentially,...
I would like some guidance on how to start a project using the nRf52840 - i.e., what sample programs would I start with? The project is a remote control lighting application...
I used the example pin_change_int from peripheral examples and commented the OUT pins. In addition I added the sleep commands to the main while loop. This is the code:
...
Hello everyone,
I'm currently working on a project that requires a nrf52832 chip to relay raw beacon data over UART to an esp-12F module. I am having a difficult time figuring...
Hi.
I have NRF52 DK.
I have successfully flashed TWI sensor example on to the board.
However, when I move forward with other projects in SDK like ble_app_uart and ble_app_blinky...
Hi I wanted to ask if there is a driver/library for the mcp25625 chip? Also for the communication do I use " SPIM — Serial peripheral interface master with EasyDMA " or "...
I'am achieving lowest power consumption in connected mode. I can't identify source of short spikes every 40Hz when mcu is in low power mode. I'am sure that it's not application...
under code is my sdk main code and i want to change code to Sensor --I2C-- nRF52 --UART-- app but where i have to start and change ?
/* Copyright (c) 2010 - 2017, Nordic...
I've been doing some testing with Mesh DFU and I've noticed some unexpected behavior around handling missing data segments.
As I understand the Mesh DFU protocol, if a data...
I have issue about calibartion using saadc.
I use 52832, S332, SDK 15.3.0
when calibration is excuting, ANT+ and BLE is also doing.
I use low power mode in saadc.
...
Hi
I want to know if there is any source code of thingy91.
Because I want to follow thingy91 for making a product with the use of the same antenna, and I want to know...
Hi,
Recently, I was trying to move my project from STM to Nordic IC.
I just wonder how to implement the below codes into the nRF52832 or how to program it in Nordic environment...
Hi,
I want to set sending power(+4dBm) of NRF52810/NRF52832 with SDK 15.0.
Now,i find i should use the order of sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle,...
Using a AF_INET UDP socket on the nrf9160 I will get ENOMEM when I send a bunch of datagrams over the socket. I understand how there can be a limited number of buffers for...
I am trying to debug the dfu bootloader using SES. This is my first time using SES. I opened the example project and everything builds fine. The image loads on the device...
