Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hello,
I'm currently building a project for the nRF52 (using SDK 15.2). I need to have 2 ADC channels, 1 for temperature sensor and 1 for battery level. I figured that I...
I want to let nRF9160 communicate through UART with 3.3V logic level, but the logic level is originally 1.8V.
I have been reading nRF91_DK_User_Guide_v07.pdf, but I'm not...
Hello,
I'm working on the implementation of some custom services and I started to question why the SDK implements the service modules as instance managers (as of SDK 15...
We are having an issue with pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ). We're using the nRF52840 dongle. We have compiled and run the `heart_rate_monitor_v6...
Hi,
I want to communicate with a legacy device nrf24l01p+ based using a nrf52840 DK.
Firmware of legacy device setup the card in this way:
I take the esb_ptx esample...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am looking to check signal strength and would like to be able to do it as easily as possible.
The default asset_tracker sends messages which can be seen in the nrfcloud...
We have an application running on our devices that are using ble_nus to communicate with a base station.
The use case is approximately something like this:
On button presses...
Step1 : init a Client model in Provisoner:
Step2 :config this client:
Step3:set the pub address of this client & control the remote gen_onoff_Server model: but it...
Hi
I've found an issue with the serialization code for the function sd_ble_gap_device_name_get in the SDK 14.1.0. As far as I see the issue still exists in the SDK15.0.0...
Why did Nordic deprecate the -30dBm TX power setting on the nRF52832? The current TX power settings jump from -40dBm all the way up to -20dBm, Why the power jump of 100X?...
HI Nordic Team :
Our important customer uses nRF52832 to develop bluetooth key product . they want to know how long the 52832 enter IDLE mode by calling WFI instruction...
I am using nrf52832, SDK 15.2, Softdevice 6.1, Embedded Studio to program a custom PCB device. My aim is to eventually send data I have from a peripheral device (through SPI...
Hello Nordic Support,
I would like to know if I don't specify the CFLAG -mfloat-abi but have floating point calculations in my code for NRF52832 target, does the compiler...
Hi,
I use NRF52840 on a custom board. I am utilizing low-level SoftDevice flash API for accessing flash:
sd_flash_page_erase() and sd_flash_write().
I want to register...
