Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi,
I'm using nus for the sensor works with uart 57600 baud rate.
Few munites later connection is broken. I don't know why.
Can anybody know this issue?
Waiting...
Just test SDK14.20 serial DFU demo project on Nordic PCA10040 board by USB serial.
Got below exception. Any clue for it please?
Thanks.
C:\gxf\nrfutil\nordic>..\nrfutil...
Hello,
I want to modify the NRF logging module to include the line number where the log was originated.
In the past I created a wrapper macro that called NRF_LOG_INFO...
Hi all,
I am using nRF82532 board. This board TX,RX(P0.06,p.0.08) pins connected with QUECTEL module in ZEPHYR sdk platform . Please forgive me for these basic doubts. ...
HI,
I want to work nRF52 thingy with segger embedded studio.
Is there any example code to compile and run the Project file for nRF52_thingy?
Which sdk need to use SDK13...
Hello,
I'm trying to autoconnect my device to my phone using nrf Connect app. I connect to my board selecting autoconnect flag, then insert my passkey and devices are correctly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
