Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello, I am a beginner with the nRF51822, after reading documentation and posts on this forum I can not find a clear answer for these two questions: - Is it possible to modify...
Hello, My software project is based on the ble_app_uart, and after doing some initial timer, PWM and SAADC initialisation tasks, the main loop of ble_app_uart runs for a while...
Hello,
I've got some of the nRF5_SDK_15.0.0_a53641a examples running on my board, the blinky, twi scan etc. all work fine. The twi and spi examples still use the legacy...
I am trying to debug the DFU in IAR.
However, when flashing as is I get the following error:
Sat Aug 25, 2018 20:31:45: ELF/DWARF Error: Unsupported .debug_info format...
In migrating an existing application from SDK 14.0.0 to SDK 14.2.0, I am finding that the first timer I create gets NRF_ERROR_INVALID_STATE on calling app_timer_create() ...
Hello,
I've got the PCA10040 dev kit and it works fine. To match my PCB setup I've cut SB2, this disables the 32kHz osc.
For debugging purposes I went back to the examples...
Hi,
I face a problem when trying to perform a DFU firmware update via command line using nrfutil dfu ble.
I'm using windows 10 and nrfutil.exe version 3.5.0
I am using...
Hi,
In application note 'nWP017 - Antenna tuning', it provides quite a lot information about how to tune antenna.
But, once it is properly tuned, how do I know the matching...
Hi,
When I do not call advertising_start(erase_bonds); then I only draw about 2uA.
When I call advertising_start(erase_bonds); I draw 350uA.
I want to advertise. Then...
Hello Nordic Team,
I have few analog sensors that operate at 5V DC and outputs voltage signal within 0.5V - 4.5V range. I know i cannot interface these sensors with nrf52832...
Hi,
I am working on a project with nRF24L01P. Recently I was trying to make nRF24L01P to transmit packet continuously and i have configure the chip in no_ack, TX and shockburst...
I am using nrf52832 based on SDK14.2 development. I used the air upgrade method in the routine "buttonless dfu". After the online upgrade is successful, nrf52832 will be automatically...
Hi,
we have a nrf51 mounted inside an AC motor housing which we assume is causing an unintended flash erase from time to time (checked with nrfjprog --readcode).
Is...
Hi,
We have a custom board with a Telit Bluetooth module, Bluemod+s42, now.
At present, I am using the "nRF Mesh" APP to test the feature of proxy. But, I encountered...
https://devzone.nordicsemi.com/f/nordic-q-a/29255/mtu-size-of-nrf52832-as-central has the answer of how to change MTU size. Could you please provide more details with the...
