I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
Hi,
Which service should I use for temperature non-health related, like room temperature, for example? I have browsed trough the Gatt Specification>Services of the Bluetooth...
Hello,
I follow the tutorial devzone.nordicsemi.com/.../
And in the step of copy examples
I only got ble_app_uart_s130_pca10028
and no package of s110 was found
I'm...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
hi ken：
I use Nrf52832(S132) to act as central and peripheral at the same time, which like the project ...\nRF52_SDK_0.9.0_0c82e3e\examples\ble_central_and_peripheral\experimental...
Hi,
I run ADC mudule together with SD, but go into hardfault eatch when I release the HF-clock.
Chip: 51822
SDK : 10.0-alpha
IDE : Keil-472
I use this function...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
