I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi, i currently use nrf54L15 and PPK2 in ampere measurement mode.
nrf54l15-DK is PCA10156 1.0.0 2026.37 and PPK 2 is PCA63100 1.1.2 2026.29
For testing purpose i use the...
Hi! We have a device that includes boost converters powered from the battery through the nPM1300.
When these converters are enabled, a short but relatively high current...
I'm aware of https://devzone.nordicsemi.com/f/nordic-q-a/125252/reset-over-ctrl-ap/555253?focus=true
Is it possible for an nRF54 to safely use the CPU access to the AP registers...
Dear Nordic，
The device occasionally fails to receive packets sent by the power switch, but Wireshark can capture packets.The button itself is the trigger and power source...
I understand that the NRF54LM20 reference suggests not to put any sort of resistor or capacitor components on the reset pin and simply rely on the internal pullup. Since this...
Hello, I recently bought the nRF93M1-DK from Mouser for evaluation in the USA. I was trying to get either the included SIM or a separate known good IOT SIM I already have...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Hi,
We're moving a USB product from an FTDI bridge (FTDI's own VID/PID) to native USB on the
nRF52840, and need to settle its USB identity before release.
Setup...
The nRF7002 datasheet lists that the current draw for maximum power transmits is ~170 - 260mA depending on frequency and if you are using the CSP or QFN package. Please confirm...
Hi,
I am currently in the initial research stage of my project. My objective is to explore adding Google Find Hub functionality to a Bluetooth device so that it can be located...
The Thingy:91 X board files allocate only 32 kB to the TF-M secure partition (slot0_s_partition). This is too small to support CONFIG_TFM_PROFILE_TYPE_MEDIUM, which is required...
I’m building a Matter device on the nRF54L15DK with nRF Connect SDK v3.4.1 (Zephyr 4.4.2). The device has two plug endpoints, 1 and 2. I started from the Matter sample and...
