Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,
I go my own hardware, that connects the nRF52840 Module to an ST25R3916b-aq chip with SPI bus. The I2C bus is also available by using some 0R resistors, just in case...
HI Nordic support team.
I have a question relate to RSSI in proprietary_rf application.
We test on esb_low_power_ptx.
Can i read RSSI of esb_low_power_ptx?
thanks...
Hi. I'm using NCS V2.6.1 with nrf52833, and I'm trying to merge the “zephyr\samples\bluetooth\iso_connected_benchmark” sample application with the “nrf\samples\mpsl\timeslot...
Hi Nordic support team.
I incharg project replace NRF24l01 by new design with nrf52833.
Using nRF5_SDK_17.0.2 and segger studio compiler.
I using esb_tx example, the...
Nordic DFU SDK version 2.5.0. Github issue here .
When the Android screen is off, the DFU fails right after starting. This appears to be because the scanner cannot find...
Hi, I have a project using the chip nRF52832 and sdk nRF5 14.2, I'm updating the firmware to use the nRF Connect SDK 2.2(NCS).
In my project, i use spi0 and spi2, so a can...
Hi.
I start SPI as well as I2C at the same time . then build code , the build error is occur . below is error code .
The SPI and I2C cannot be used at...
Hello,
I try to building sample code nrf_dm for nrf5340DK, but I got failed massage:
.7.0-rc2/nrf/subsys/dm/dm.c.obj -c C:/ncs/v2.7.0-rc2/nrf/subsys/dm/dm.c C:/ncs/v2...
Good Morning
Im using Zephyr, SDK2.6, toolchain 2.6. the peripheral_uart example is flashed to a 52840DK. when I connect with my phone IOS NRF_connect I get the error
...
I run the LWM2M client and send the data to the server. Nrf7002dk connects to the internet via wifi. Now I would like to update the software but I can't seem to do it. The...
Hi, I want to implement OpenThread features with another sample and I'm not sure how to go about it. Is it even a good idea to add OpenThread to another sample or is it better...
I use the serial port routine SDK17.1, nRF52833 want to burn the protocol stack, s113_nrf52_7.2.0_softdevice. But when I burn it to the chip, the address is 0x1000 and if...
Hello I have a board that I am trying to profile with the power profiler kit 2 and the readings seem very wild. I have a device that I know the base configuration with the...
I have a customized PCB with nrf52840. Pin 0.18 is used as CS pin in SPI communication.
I want to disable the nreset function and I add this CONFIG_GPIO_AS_PINRESET=n in...
I'm using the CLI interface through USB and UART, and I am wondering if there are any innate methods for checking the validity of the data being sent and received via the...
