I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello everyone.
I'm developing a custom board mounting the nRF5340, and I want to use the micro USB. I was looking at the schematic of the DK for reference, and I found...
Hi,
Not sure if this is the correct place to ask...
My code is crashing after a spi write function.
It is probally obvious to someone here, i think i fell into that...
I'm attempting to merge 3 HEX files into one using the Merghex command. The "BinaryImage access" error appears, see the screenshot below.
I've tried this several times with...
Hi,
I'm porting my SSD1333 (Solomon IC for OLED displays) code driver to Zephyr OS drivers for ease of use along with LVGL (going from `< nrfx_spim.h>` to `<drivers/spi...
I want to transfer a bunch of data over the virtual com port to a PC using the USB port on the nrf5340. I'm using the CDC ACM sample: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
why
AT%XRFTEST=1,1,14,7880,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7930,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7980,23,1,4,0,0,0,0,0,0
returns ERROR but e.g.
AT%XRFTEST...
We are trying to see if it is possible to detect a vibration using the ADXL362 accelerometer on the Thing:91. We have it setup to to trigger on motion, but we need to be able...
Dear all
I following the example here , over the air one, and get it basically working, thanks for the tutorial.
Now I have a few questions:
1. It looks like it always...
Hi
I am studying Matter, my setup is
chip-tool : chip-tool-android_armv7l.apk v2.1.0
OTBR : raspberry pi 3b + RCP( PCA10059 )
board : nRF52840-DK(PCA10056)
sample...
My pairing is working and shown as bonded on Android, but when the DK is reset, the bond is no longer valid.
In studying saving of bond information, I find references to...
Hi,
I am learning Matter. I have some questions:
Where can I get the resources, especially official resources, to study Matter?
What is the use of the Service discovery...
Hi,
We are developing our product using nrf5340. Currently, we are using NCS v1.9.1 for development. We need to give UART to test our Board for Certain conditions by using...
I have been learning to use the nrf52840DK for some time now, though I would consider myself still a beginner. Anyway, something has gone wrong with the kit and I am not sure...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
