In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
For my project I need to set the UART0 speed to 9600 baud.
So for testing I tried to compile the "Hello word" example by setting the board configuration file (ncs\v1.6.1...
CONFIGURACION:
NRF52 + SDK15 + SD132 + FREERTOS + NUS.
I have a task sending many packages to a central. I'm having an aboslutly aleatory behaviour: - At some time (could...
I’m checking the transaction of the data between iPhone and a Bluetooth device.
The device is developed by a business partner, but I’m not concerned the FW. I think we have...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
Hi,
I've designed a product based on nrf52840 soc as a central Bluetooth device. I want to pair and connect to a Bluetooth device (as a slave) that implements a whitelist...
Hello,
When AGPS is activated and trying to fix location, the user see only the final respond once fix is done, but we need to know where the satellites table is stored...
nRF21540
We want to use the nRF21540 FEM to improve BLE range and performance within a building. How does the Tx and Rx amplifier operation coordinate with the BLE SoftDevice...
Hi,
Related to this topic BLE DFU, MCU to MCU (Zephyr), GATT DFU SMP Service Clinet
I would like to know if anyone has any luck in making a SMP client for DFU updates...
I moved to a new computer and reinstalled all the tools and moved my code over. Now, when I compile, I get the following error:
Here is the code from the board definition...
I have an nRF9160DK that I'm trying to get a demo running per this video: https://www.youtube.com/watch?v=rMvW3HXLErk&t=832s
The board label says PCA10090, 0.8.5, 2019...
I had used ble_advertising_advdata_update function to update my scan response data in ibeacon by getting error as mentioned below:
.\_build\nrf52832_xxaa.axf: Error: L6218E...
