Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
Hello,
I was trying to get a Thingy:91 to run asset_tracker_v2 with an external GPS antenna connected to the U.FL.
NCS 1.7.0.
Based on the Thingy:91, I was trying...
Hello,
I am currently developing an application using as template the ble_app_uart.
My application works fine so far but we would like to add as a feature the pairing...
Hi All,
I am trying to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial without pressing BUTTON 1 and RESET buttons in nrf52840...
Hello, I am using sample hello_world app in SES, in the main file of which there are two print statements as: During flashing and debugging on the board, execution enters...
Good day to you,
I cannot find any reference/documentation whatsoever that relates to the following type of code... 4 lines of example code is below (from this link https...
Hi All,
I am trying to do Device Firmware Update (DFU) with MCUBoot bootloader for nrf52840 DK and I am following this link https://devzone.nordicsemi.com/guides/nrf-connect...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am reading and writing data using FDS. If you execute fds_record_update at that time, the error of...
Hello,
I'm using the off the shelf Asset Tracker V2 and the application is sending GPS position and other sensor measurement at every 2 minutes.
Is there a CONF to change...
Hello developers,
I saw the process of bluetooth scanning from nordic infocenter.
Scanning for advertisers performing legacy advertising
In this picture, I don't understand...
Hello,
I have an application that runs on a 9160 which uses mbedtls (via TFM) to connect to an AWS server. The application is using a CA that you folks have given me in...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
