Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
nRF Connect V 1.6.0
using samples/zigbee/network_coordinator against a nRF52840, I am trying to commission a larger number of devices to join the network. Currently 24 devices...
Firstly, my english is not good,
I am using nRF52840 and my IDE is Keil uvision 5, i want to know, where is the pins SDL and SDA
I am new developer, and please you can...
I have successfully formed a mesh and sending data in the format as below
" udp send ff03::1 1234 $01 " to udp '1234' socket
" udp send ff03::1 1234 $02 " to udp '1234...
Hello everyone,
I am currently testing the range of Nordic BLE modules for an indoor application. I am using BC805 (nRF52805) as peripheral and BM832 (nRF52810) as central...
I am re-implementing a custom error handler that stores error data and forms an error report after reboot, after having a success with it in nRF SDK 15.
In nRF SDK I could...
Hi,
I'm using Windows 10, Wireshark 3.2.17, python 3.9, pyserial 3.5.
I see this question has been asked before but the solutions did not work for me.
I get the...
Installed pynrfjprog on Ubunto 20.04 (native) via pip. Can open Highlevel api etc, however fails to detect nRF52 dev board as s probe and the logs indicate DLL failure.
...
I'm sorry, I don't know how this is reproduceable.
Yesterday and today my connection does not work. Sometimes . Yesterday it was OK early in the morning and in the afternoon...
I am using the SDK v17 with the Mesh SDK v5 and the nRF52 development kits and I'm using SEGGER.
SETUP: I have a mesh network with: 1 dimming client
1 dimming server ...
Hey Guys, currently, I am working on my masterthesis. I have to develop an mobile application which comminicates with the nordic board via BLE. I know that there is an existing...
Can you please clarify the typical eSIM current consumption when using eDRX?
Is the eSIM module on all the time? If so, what is the typical consumption?
If possible to...
The code shown below filters the duplicate MAC addresses, but I found in the previous development process that many Bluetooth devices only display the MAC address, not the...
Hii all,
i have a NRF52832 board with some sensors ..I coded it with SEGGER Embedded Studio . i Build and flashed and RUN successfully,
But after Disconnecting the board...
Hello , I am using the DTM in the NRF Connect.
Does you packet count preforms any CRC or other verification when receiving packets? I can not find any mention of BER (Bit...
