Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi,
Question:
In our project we need to drive some external components (High Side Drivers) via GPIO output.
In order switch on our “High Side Drivers” we need a voltage...
I'm using TWI and BLE functions together. My TWI sensor is operating at 400kHz, low priority. BLE has the highest priority. For example, if nRF52805 is sending commands to...
Hello community, I tried to read my motor encoders with the QDEC and capture the position of my motor. Hardware: nRF52840 DK, 2 Hal motor encoders on pin 0.13 and 0.14 which...
In NCS v1.6.99 the HEX data format is removed from data send and receive commands (socket, udp/tcp cli/srv), only ascii and data mode is supported.
In case of binary data...
Hello,
First time post and brand new to the nRF52832 chip. I am tasked with building firmware that will synchronize ADC samples across multiple devices. I have started with...
Hi to all team,
I have two units of nrf52840 dongle with me.
I have to develop the generic application firmware where data send from one dongle(coordinator) is getting...
Hi,
I have built ble board with nrf52832 with no pca10040 on my board and i have assign button switch pin as P.0.13 from nrf52832.Previously i am using nrf52832 dev kit...
Hello,
I have a custom example based on the "asset_tracker" application of the SDK v1.3.1 and I am trying to open the IDE through Toolchain Manager, but when I select "OPEN...
hi support team,
i was testing usb dfu(NCS1.6.0) function with window10, after i download the code, the windows seems not able to install the driver as below, and i couldn...
Just a naive question about the definition of nrf_fstorage_t , it has a member nrf_fstorage_info_t *p_flash_info .
Why the type isn't nrf_fstorage_info_t const* ?
Tell...
Hi,
there should be OK response after #XSLEEP before enter into sleep to notify, that command was received and processed without errors.
Current implementation (NCS v1...
device: nRF52832
SDK: nRF5 v15.3.0 (s132)
Soft Device: 6.1.1
I am trying to read multiple fds records and transmit them to the central device (nRF Connect on android...
SDK: 15.3.0
I have developed PCA10056 board based on CLI example.
I tried to print debug strings.
but, [00: 00: 32.310,668] <warning> app: Prints backends flushed repeatedly...
