Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
Hi Nordic Team,
In my BLE project, first the central device starts scanning, then the peripheral device starts advertising, the peripheral device gets connected to central...
HI,
I got nrfutil + BLE DFU app update working using the ble_app_hrs for the test. I am using the nrf52DK + SES for development, and I have also an external nrf52832...
Hi
I'm using this simple_pwm code to drive my speaker, I use this as a buzzer but I want to change the frequency.
In this code ".base_clock = NRF_PWM_CLK_125kHz", the...
Hi, I am developing an IMU app communication with ESB. I would like to send to the board a command with ESB to put the nrf52832 board in BLE DFU mode.
I have look at the...
I am using the timeslot API, and I have noticed that if I read Timer0 as the first thing in my timeslot, it will be at 75 us. This delay is very consistent, so my timing between...
The following change was introduced in v4.0.0
Note that mesh_config_clear() was replaced with mesh_opt_clear() which is a rather big change of behavior that wasn't documented...
Hi,
Just trying to run mqtt sample with TLS and AWS IoT backend. Everything worked fine in the beginning, but then after I tweaked the code a bit I suddenly started getting...
Hello,
I'm using SDK5 v16.0 and softdevice S140 v7.0.1.
At some of the PCs, it takes much longer than usual to upload the zip package. On my machine, the transfer rate...
Errata 182 needs to be applied (in revision 2 devices) to enable the fix for erratas 102, 106 and 107. The workarounds for these erratas all stated that they reduced receive...
Hi,
I am using NRF51822 SDK12 S130, I have increased my code and encountered a crash right at the beginning, I debugged it as follows -
I increase an integer ( uint32...
Hi,
I was wondering if I could get a little information on how to set a pin as High Impedance using the zephyr gpio.h library.
We have a shared pin between a nRF9160 and...
Is there a value or values range defined for the user cmd/evt in the serial interface?
I would like to use the uart for some app specific operations, and could use packet...
Hello. I'm having problems to programme the nRF52832. I'm just connecting the VCC (+3,3V), GND and SWDIO and SWDCLK. Is it ncessary to connect any other devices like capacitors...
Hello,
I have been using the buttonless DFU method for a while on the nrf52832 Chip. Due to performances need we changed the chip for our product from nrf52832 to nrf52840...
