In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello all,
I've been working on creating a test app for a product that I've been developing for sometime. It has multiple BLE services such as Device information (DIS),...
HI ,
On my costume board works fine when VDD connected to ~3.6v.
it starts to behave differently when voltage is ~4.1v. (Flashing fails / SW not loading ).
my VDD_GPIO...
Good morning, I am a university student and I would like to know if there is a tutorial or an example to do a simple test of the operation of the new feature of Bluetooth...
I am trying to read ADC values for 8 different channel, in order. It's just to test if the ADC and its API.
I successfully receive the ADC binding (it returns 0), and the...
Affects version: SDK 15.2.0
Building the ble_app_hrs_freertos example produces several warnings in SES. The warnings are related to redefinition of several MACROs.
I have set up a custom board using the nRF52811 based BMD-360 module.
I have tested the twi_scanner example, first of the nrf52DK with an external sensor. I Changed the...
Hi all,
I'm trying to get the Thingy device work with (SEGGER's) RTT. I used the asset_tracker sample application and edited it to just print to RTT in a loop after all...
Hello,
I am having an issue with the nRF52833. I'm using the NRF5SDK, version 16, and the SoftDevice s113 version 7.0.1. I can take the ble_app_uart example from the sdk...
Hi everyone,
I am looking at sending data via HTTPS to Azure.
I have used the https_sample and modified it to send the data to Azure with no issue. But now I am trying...
Hi Nordic Support Team,
I am planning to use nRF9160 Customised Board for NB-IOT Application.
I want to make it battery Operated Device.
As i want to know how Communication...
Hello,
I am using SDK 15.3 for the development. During the upgrade process I wanted to send the hardware version when requested by the host.
I have made the changes...
I want to use P0.10 of NRF52810 as GPIO. I have added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS in the make file. But still its not working. I am using Nrf 52810 , SDK 15.2.0...
Hello,
I recently decided to upgrade an Arduino project to you nice and well documented products :)
I successfully built and run the example provided here and tried...
Hello! I'm interfacing a sensor with an nRF52840 development board and have run into a few issues:
1) I have a check status function as shown below:
bool ADXL_check_status...
Hello, I'm working on timeslot and RADIO on nRF52840.
I found a sample code which sets 1 to "NRF_RADIO->POWER" to initialize RADIO peripheral.
-----------------------...
