Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
i'm using this dongle USB840F based on nRF52480.
i'm using usbd_ble_uart_freertos (SDK 15.2) example, the usb port is detected and i can read from it , but it doesn't advertise...
Hello
I'm surprised to see this kind of power profile when the device is in advertising mode.
The 3 TX steps for the 3 canals of advertising haven't got the same max...
Good day,
I wish to adapt the Eddystone Beacon example for nRF51822 with S130 in e.g.:
..\nRF5_SDK_12.3.0\examples\ble_peripheral\ble_app_beacon\pca10028\s130\armgcc ...
In my application, the nRF52840 dongle is hard-wired via UART port pins to the UART interface of a Wi-Fi gateway host board. I need the nRF52 application to restart when it...
As a final step to the legitimate dual bank-based application DFU , the existing application will be replaced by the new application.
What happens if an internal error...
Hello,
Is it somehow possible to output a 13.56 MHz signal from the nRF52 ?
Yes, I KNOW: Similar questions have been asked many times. The nRF52 cannot drive an 13.56Mhz...
Hi,Nordic Teams:
I have emergent proble ,can you help me?
1.in light_switch example provisioner,there is some code below:
2.when provisoning ,we can setup a node to...
So I run SDK 15.0. I have a notification channel, and I want to transmit some data on it.
I run this code
hvx_params.handle = gatt_notify_handlers[index].gatt_handle;...
I'm using the nRF52840 to interface with an existing 802.15.4 network. For reasons decided long before I became involved, the messages exchanged are MAC command frames, not...
Hi,
I am testing BLE throughput between NRF52832 and iPhone XR using S132 stack. I am able to get maximum of 400Kbps. Is there a way to achieve throughput better than...
Hi,
I am trying to design the transmission lines based on the reference board design from Nordic.
I opened up the Altium layout file for the board which I downloaded...
I'm trying to communicate with HTS221 sensor and read WHO_IM_I but then I always get error 17 on nrf_drv_twi_rx and receive 0 on output
Twi init
ret_code_t ret;
const...
Hi
I want to use TWI read temperature from sensor Si7050, but i got a problem that doesn't jump into twi handler event. Can anyone give me some information? Thank you. ...
Hi,
This is somewhat tricky question..
Does GAP broadcaster differ with the BLE device which advertise packets with non-connectable option?
Is The device which operates...
