In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
I am making a BLE device that uses 7 ADC inputs. Most of the inputs need to read at 1hz or so. Two of these inputs are of interest
The first is a heart-rate signal that...
Hi,
I want to measure ADC for 3.3V
Using formula
RESULT = [V(P) – V(N) ] * GAIN/REFERENCE * 2 (RESOLUTION - m)
Rearranging eqn:
Vin = ( RESULT*REFERENCE)/(2 (RESOLUTION...
Hi,
Does every nrf9160 chip have its unique chip ID? if yes, is it the one which can be read by the AT command AT+CGSN ? and can it be used as the board serial number? ...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
We are using nRf52840 chip with Nordic SDK 15.0 version using SES IDE. When we use debug mode in build configurations program is not working or not debugging got error as...
Hello All,
We are trying to use nrf52810 with S112 soft device and 14.2 SDK.
We have problems with random disconnection with error number 8. This happens when central...
Hello,
I am attempting to run the Nordic-Thingy52-mesh-demo using nRF Mesh v 1.1.0 for Android but the nRF Mesh app's scanner cannot see my DKs. I can see the mesh from...
Hello All,
We are attempting to instrument our software and yours. The desired output is data for a call-graph list and time stamps for each entry and exit into a function...
Why does the pushing a button located at GPIO_9 not call the interrupt handler and therefore print the statement to RTT?
#include "GPIO.h"
#include "app_error.h"
#include...
We are currently using nRF51822-CEAA rev2 on the production boards. As this part is obsolete, I was made aware of nRF51822-CEAA rev3 as a replacement . So I have some questions...
