I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 and S132 SoftDevice v6.1.0 to do some tests . But now I encounter the disconnect reason 0x22...
Hi,
I'm using nus for the sensor works with uart 57600 baud rate.
Few munites later connection is broken. I don't know why.
Can anybody know this issue?
Waiting...
Just test SDK14.20 serial DFU demo project on Nordic PCA10040 board by USB serial.
Got below exception. Any clue for it please?
Thanks.
C:\gxf\nrfutil\nordic>..\nrfutil...
Hello,
I want to modify the NRF logging module to include the line number where the log was originated.
In the past I created a wrapper macro that called NRF_LOG_INFO...
Hi all,
I am using nRF82532 board. This board TX,RX(P0.06,p.0.08) pins connected with QUECTEL module in ZEPHYR sdk platform . Please forgive me for these basic doubts. ...
HI,
I want to work nRF52 thingy with segger embedded studio.
Is there any example code to compile and run the Project file for nRF52_thingy?
Which sdk need to use SDK13...
Hello,
I'm trying to autoconnect my device to my phone using nrf Connect app. I connect to my board selecting autoconnect flag, then insert my passkey and devices are correctly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
