I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
First of all, I see that NRF52840 doesn't have a Real Time Clock but it has a Real Time Counter which is not working in case of sleep and low power mode, am I correct?
Second...
Hey everyone,
I am having trouble setting up the lsm6dsv16x as a interrupt. I was able to successfully poll the data meaning I can talk and read imu data, but no interrupt...
Hi , I wanna keep my existing mobile application which talks to nRF5340 over the BLE NUS service. I am using the default BT_UUID_NUS_VAL as my primary mode of communication...
I want to edit the explom firmware that comes with thingy91 to add the reading of new sensors and send them to nrf cloud. Where can I get the example of the Asset Tracker...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
Hello,
I’m having issues with time synchronization when using the sidewalk Sub-GHz template from SDK v2.5.0. My setup includes a Nordic Semiconductor chip nrf52840 and LR1110...
What is the reason for the default 320 hour setting for periodic Tau timer? This seems like an awfully long time, and we're wondering if this is simply a placeholder, or if...
Hi. I'm finally bought a PPK2 to test some of self-built IoT devices. I do have a question in regard to the device (before I break anything). Does it offer any types of short...
