Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hello,
We want to use a nrf52840 as a logic controller which reads data from Modbus RTU Sensors (as Modbus RTU Master) and simultaneously is the Modbus RTU Server for an...
Hello Team,
We are trying to make Release and Debug mode for our software.When I compile a sample program I see lot of Debug information in the Mapfile. Will this influnce...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hello,
When building my project although the terminal doesn't show me using all the RAM, I get the following error message which fails the build.
I am using a...
Hello,
I was working on a ble communication using two nrf52dk boards while one of the two stop responding. The board is correctly recognised by the computer and segger asks...
When I am on to collect the accelerometer data from Thingy-53, only 3 sampling frequency options are provided which are 20 Hz, 62.5 Hz and 100 Hz as shown in figure. Please...
I am new to nRF chips and currently working with the nRF52810. I am developing with nRF Connect SDK and VSCode.
I have encountered an issue with the Blinky example (ncs...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Running the Ciphersuites sample code on the nRF9161 I get Connection Refused on all attempted ciphersuites. Including after adding the CONFIG_EXTENDED_CIPHERSUITE_LIST=y to...
Hello,
Dev board: nRF52840 development board.
OS: Zephyr (NCS v2.6.0).
My requirement and What I am using...
- I want to perform DFU for application core & bootloader...
Hello Nordic Team, I am using nRF5340-DK and I have a PPK-2 for current measurements. My development environment is NRF Connect SDK v2.5.2. I used https://infocenter.nordicsemi...
Hello,
I am using the "direction finding connectionless beacon sample" to test various settings of the beacon. About setting parameters, I have the following two questions...
Hi. I'm working on a BLE system with Central and Peripheral with nRF5340 with 70msec of CONN_INTERVAL and about 1sec of SUP_TIMEOUT. The Central unit also has a UART that...
HI
In the RF_Test example, there are 80 channels.
However, BLE has only 40 actual channels.
Why are there 40 channels...? I would like to know.
Do 80 channels...
