Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I`m using Ble Mesh Light and Light Switch examples (Gen OnOff models) in two nrf52840 Dongles. The default configuration of the button is that when I pressed the button in...
Hi,
I am trying to interface arducam mini 2mp ov2640 with nrf52840 and I am referring the following github repository: https://github.com/NordicPlayground/nrf52-ble-image...
Hi everyone,
I try to implement DFU on nrf52840 with SDK15.3 and softdevice s140.
I use the secure bootloader ble example and in BLE it works well. But I have an issue...
Hello,
I'm currently developing some firmware for the nrf52811. i currently ran into an memory issue and got stuck there.
i have started from the ble_app_templater from...
Hello
I got error in getting the mac address with available answer( devzone.nordicsemi.com/.../how-to-get-mac-address-using-nrf5340_dk) in forum. I tried to paste that code...
Hello,
I got saadc example on my nrf5340 dk running and now I would like to plot the incoming serial data.
saadc code example: saadc.zip
changed the way I got adviced...
Hello
I use the sample project for alarm (zephyr/samples/drivers/counter/alarm). I was able to build the sample and run it on NRF52DK (PCA10040) with NRF52832.
I tried...
Hi,
I am using window 10
I am trying to connect to the nRF52 DK, but it does not show me the files on the board as it is explained in the how to connect to the DK.
Also...
I have successfully built my project in VS-code for the Thingy:53. Because I don't Have a debug probe I cannot flash the firmware from VS-CODE. What are the files that need...
I was using Power Profiler app with PPK2 for capturing data on long period(48 hours) after 2 hours of running the app is crashed.
Detailed Error message
System Report...
So I am using an nRF5340DK with the "central-bas" example project. I added the MCUBoot-Bootloader by adding "CONFIG_BOOTLOADER_MCUBOOT=y" to the prj.conf file and it works...
I am implementing a port for nRF52832 for our custom communication stack. Devices are time-synchronized, radio operates in destined time slots. During the radio inactivity...
Hi all,
I am using NRF5340 with nRF Connect SDK v1.9.1. And I want to add my own .h and .lib(GCC) file into my project.
Please tell me how to do.
Thanks a lot!
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 My project base: \nrf\samples\bluetooth\peripheral_hids_keyboard
Hello. I want to increase Tx power for test. I already...
