Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
How are private keys stored on the nrf9160 modem? I've read in other forum posts and observed that the private key cannot be read out once set in the modem. Where could I...
According to this discussion, all the 4 UARTs are functional in nRF5340. I intend to use multiple UART ports, and I modified this exercise solution to do so. I was able to...
Hi new to this, so excuse the elementary question
Can I put custom software on a XM122 using the XB122 dev kit? This is the only hardware I have, is nRFUtil my only option...
nRF52840 does not mention medical as one of the application areas. Is there any specific reason for this? Any hardware or software requirements not met in order to use it...
Hi, I tested Central HIDS example in nRF Connect SDK 2.1.0 with NRF52840DK. The example works with my BLE keyboard, but does not work with my BLE mice. The followings are...
I am unable to use UART 1 with a very simple use case.
All I need to do is enable an interrupt callback when there is data to receive from the UART. I know that UART0 is...
Hi
I am facing range issue in transmitting and receiving data over ZigBee in nrf53833, how can i improve the range maximum i am able to recieve signal from around 35 feet...
Hi All!
I am using Zephyr RTOS NCS v2.0.2.I used uart_central and uart_peripheral apps. But it Can only connect one peripheral with central at a time. Is it possible to...
Dear Nordic,
I am currently working on a USB project were I am interested in building a USB audio device with two-way volume control, i.e. such that both host and the device...
Hi
I am trying to connect my own mosquito MQTT broker. I created certificates and I uploaded all certs through the LTE Link Monitor. I defined
CONFIG_AWS_IOT_BROKER_HOST_NAME...
Hi,
I have been working on a setup where I connect a sensor (TI ADS1299) to the nRF5340-DK 2.0.0 using an SPI connection and transmit the recorded data using BLE. I have...
Hi team,
I am using NRF52833 DK with PCA10100 on it and s140 soft device version..
While writing data into the flash, it is not updating.
Here I am attaching my fds...
My device and Software details are as below
nRF52840 DK
nRF connect SDK 2.0.2
Want to verify USB device role for nRF52840 DK.
Found the below example and its documentation...
Dear Nordic Support,
Please help me with following.
Hardware - Thingy:91 1.0.0 (2019.43) PCA20035
OS - Windows 10 64 Bit
Laptop - HP core i5, 8GBRAM
I want...
