Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hello. I am using NRF SDK 1.9 version + VS Code to process accelerometer data. NRF52840 + ADXL375 The accelerometer is configured to issue an interrupt under a certain condition...
Dear Nordic Engineers
I would like to sample the ADC between advertisements or connections, that is when the RF is sleeping, so I want to use Timeslot, I see there is a...
I am trying nrf52840. The conditions are as follows. -The development environment is SEGGER. -nRF5_SDK_17.1.0 -The evaluation board is a DK from Raytac. There are two identical...
Hello,
I'm starting a new project on a NRF52810, and i need to use the pairing feature in my application. As a result i need to compile the FDS driver. If i'm doing so,...
Hello,
I have setup a single master and multiple slaves (10 in number).
The master has master TX channel and the slaves have slave RX channels.
The slaves send data...
Hi, I am working on ble_app_uart_c_pca10056_s140 project. I have changed the following for power saving. Is this the right way to achieve this mode? After how much time it...
I used this code to convert my analog sensor data to digital with 5 khz continuous sampling and after that i want to sent my data to pc via BLE. In this code, NUS was used...
I'm using a custom battery operated board with the nRF52840, when there is no GPIO events for a specified time period, the device goes to a hibernate mode using the __WFE...
I am currently working with a dvk-bl653 working on increasing the speed of the DFU. I have a max packet size of 251 and have tried different connection intervals but only...
Hi again
I have used nrfConnect to create an application from sample, the sample being peripheral_hr_coded
I have placed my custom service into the app, and it works...
Hello, I am trying to measure the input voltage on an nRF52833 and it is not behaving as expected.
The following code is taken from here and works as expected on any nRF52832...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
