I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
I have two Adafruit feather with nRF52832 on them, using one as central and the other as peripheral.
I have created some codes based on ble_app_uart from Nordic SDK and...
Hello,
I'm trying to program the NRF5340 DK board on linux. However, the board doesn't show up when I run `nrfjprog -i`. It doesn't show up when I run lsusb. `udevadm monitor...
I'm struggling to get a Micron MT25QU128ABA ( https://media-www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/mt25q/die-rev-a/mt25q_qlhs_u_128_aba_0...
Dear Community,
We want to use bonding to connect our app to the nRF and create a personal account.
So all your devices will have the same UUID. If the device never connected...
We're working on a board with an nRF52840 running BLE with softdevice S140 and SDK 17. The board has an external SPI flash, and when we realized that SPIM3 can be run at higher...
I want to know if I call the following function, which condition should I meet to determine that the coordinator is not connected to any terminal devices. For example, I now...
Hello, I am looking for some help or example code that describes minimum set of the files and #defines required to enable AES 128bit encryption and decryption using ECB mode...
Hello,
I'm trying to learn what might be typical latencies for Bluetooth LE Audio. For instance, the aptX low latency codec claims latency around 20-40ms. Is Bluetooth LE...
Studying the documentation for the nRF52811, I found a difference in the description of memory recording and memory erasure:
write: " The CPU is halted while the NVMC is...
Hi,
I have nRF52840 DK and am using nRF5_SDK_17.0.2_d674dde.
I am not using SoftDevice, and Zephyr RTOS.
I have a simple program and using RTC0 timer. My code snippet...
Good afternoon,
I have a question regarding the nRF9160 and the eSIM configuration. We have developed a prototype PCB based on the nRF9160 DK and included an eSIM. However...
Hello,
I am trying the example of ble_app_uart and when i am building the example it gives me an error RX_PIN_NUMBER undeclared. When i load the pca10056.h i can see TX_PIN_NUMBER...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b and FreeRtos
This device has some bindings already set...
Hi,
my zigbee network for 120 sensors. if i declare 120 install codes then most of them don't work. The "zb_secur_ic_add" function works without error, "zb_secur_ic_get_list...
