Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
Hello Everyone.
I am a newbie in NRF52840 development. I have one NRF52840 device as a central device and many peripherals are getting connected to it (Max 6). Lets say...
I am currently using the 17.0.2 SDK to develop some code on the nrf52832 which involves streaming data via SPI to an external flash. I need to stream this data at a ~50KHz...
hello, I have a question need you help.
SDK:nRF5_SDK_14.2.0
MCU:nRF52810
My product is used as a central.
When the voltage of the battery supplying the product is...
I am trying to develop an application using ANT on the 52805, I have purchased the nRF52 DK as this was the recommended development kit for this device but there seems no...
I have a design that uses the NRF52810 as well as NRF9160.
For safety reasons, it must have a fuse that is about 1 ohm into the system. I'm seeing an issue after an input...
Hi, Nordic.
Our customer employs nRF51802 in their product.
They use BLE and 2.4GHz proprietary at the same time. They want to know the switch speed between the two protocol...
Howdy DevZone! I'm brand new to BLE, and have some beginner questions on the best way to architect a project for ultra-low power consumption.
Here's what I want to make...
Hi,
I'm currently developing a nr9160 full modem DFU based on sdk v1.5.0 and "fmu_fdev" ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/include/dfu/fmfu_fdev...
Hi,
I am trying to merge some features from nRF desktop into my application. More specifically, the BLE CAF features.
Now I hit a wall. I am getting a lot of Kconfig errors...
Hello
I'm testing the Release v1.6 of NRF Connect SDK in combination with our application. On Nordic NRF Connect SDK v1.5.1 we managed to get the following setup working...
