How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
Hi,
I need the SAADC of the nRF52840 to do the following:
It should sample two channels as fast as possible for a certain time (or for a certain amount of samples)....
Hello,
I have tried to upgrade a working project from ncs 1.5.0 to 1.6.0, which used the shell + console + RTT. However, long commands (more than 16 chars) seem to be truncated...
Device: nRF5340 DK
I installed the SEGGER Embedded Studio and wanted to run a sample application. But it throws an error when I click on Connect J-Link.
But I see that...
Dear friends,
When I reset 52840 DK and reopen the PyACI script , then, reloading the DB(database/example_database.json), I found the provsioned device can't be controled...
Hi sir/Madam,
Kindly provide the uplink and downlink details for the part
nRF9160.
We request you to provide the quote for 50K/Annum.
Please contact : lakshminarayanan...
Hi,
I am aware that the sdk-nrfxlib + sdk-nrf library embed a NFC library, dedicated to a ST NFC module.
In our product, we are using a NXP controller, a PN7150.
Is...
Hi everyone,
I got a question regarding the Bluetooth Mesh Time Server/Client models. I would like to propagate a common time base within my Bluetooth Mesh network by using...
I use the NCS SDK 1.5.1, the sample is use a QSPI FLASH(MX25R64), and we want to change this QSPI FLASH. we will use P25Q80H, which code should be modify?
Hi,
Can someone confirm what is the max input voltage for ADC input on nrf9160?
Documentation says
The AIN0-AIN7 inputs cannot exceed VDD _GPIO , or be lower than...
Hello everyone, I have successfully implemented the light Switch examples in the Mesh SDK. I sent the on_off data from the switch device to the light device. But what I need...
